[. . . ] has determined that this product meets the ENERGY STAR guidelines for energy efficiency grounding it on the following features. Auto Low Power This function conserves energy by lowering the set temperature of the fixing unit. In the standard setting, Auto Low Power operates automatically when 15 minutes have elapsed after completion of the last copy, with the copier remaining in the ready to copy state during that time. The time period for the Auto Low Power function can be set for 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240 minutes. 5-2 for details. Automatic Shut-Off This function achieves further energy conservation by partially turning OFF the power supply, thereby reducing energy consumption to 80W or less. [. . . ] Chapter Using the Finisher Booklet 1s2 Image insert 2s2 Mixed original APS Repeat Image quality (Very high) Thin/Thick paper Interrupt Sheet/Cover insertion Procedure z Load Transparent Film: Multi-Sheet Bypass Tray Insert a sheet of OHP transparent film of the same size as that of originals into the Multi-sheet bypass tray. Please Be Reminded! DO NOT load OHP transparent films into any other tray. It will cause paper jam. x Load Interleave Paper: Tray 1, 2, 3, or 4 Load Tray 1, 2, 3 or 4 with copy paper the same size as that of OHP transparent film. Close the RADF securely and press the AUTO RESET button to set the RADF mode. Press the APPLICATION button on the Operation panel to display the Application Selection screen. Touch "OHP Interleave" key on the Application Selection screen. The OHP Interleave Mode Selection screen will be displayed. OHP Interleave Mode Selection screen Application Selection screen 4. Touch "Blank Sheet Interleaving" or "Copy Sheet Interleaving" key. Advice To return to the initial condition, touch "CANCEL" key. When copying more than 50 originals, use RADF store mode or Platen store mode. Advice To clear all application settings, touch "ALL CLEAR" key. Image Insert Image Insert is used to combine images scanned from the platen glass with images scanned from RADF. Then, output the combined images as a finished set. Place originals onto RADF 78 1 23 45 6 78 34 1 2 5 6 Insertion originals Place originals onto RADF 6 4 2 8 6 3 5 7 5 3 1 1 2 7 4 8 Basic rules for Image Insert · Scan and store originals into memory, then print all the pages collectively. Advice If memory overflow frequently occurs, you are recommended to extend the memory. · Use the RADF store mode to scan first the originals to have insertions. · Use the Platen store mode to scan next the originals to be inserted. 999 Original paper size : A3, B4, A4R, A4, B5R, B5, A5*, 8. 5"x11"R Tray paper size : A3, B4, A4R, A4, B5R, B5, A5*, 8. 5"x11"R, 8. 5"x11" (80g/m2 paper recommended) Print quantity : 999 sets max. Advice *: Load A5 paper in lengthwise feed ( ) only. OHP Interleave Image Insert 8 - 33 Section 8 : Special Copying : Page Editing 7. Image Insert (continued) Incompatible If any of the following copying conditions are going to be set, the Image Insert copying may be cancelled or the key concerned on the screen may become faint, not allowing setting. Store mode Dual page Reserve Mixed original Image quality (Very high) Repeat Sheet/Cover insertion Auto layout Chapter Image shift Combination Non image area erase OHP interleave Procedure z Set Copying Conditions 1. Close the RADF securely and press the AUTO RESET button to set the RADF mode. Press the APPLICATION button on the Operation panel to display the Application Selection screen. [. . . ] Simple Problems Symptom Power switch is turned ON, but copier does not operate. Use the forcible ON facility , or Contact your key operator. · Close the Front door Is the Front door completely completely. Is the Tray inserted appropriate · Load appropriate size paper into Tray. Is the Left partition glass, Platen glass or RADF platen guide cover clean? [. . . ]